Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
LiftMaster Cable & Drum Replacement: The Phoenix Owner’s Guide
LiftMaster cable and drum replacement in Phoenix typically runs $130-$250 installed when we do it, depending on whether one side or both sides need new cable and drums. We stock LiftMaster-compatible cables and drums on our trucks, and most jobs are completed in about an hour once we’re at the door. The usual discovery: you’re backing out of the driveway, the door starts to open, and it either stalls halfway or makes a grinding sound like a shopping cart with a locked wheel. One cable has let go or a drum has cracked, and the door is now hanging on one side.
This page covers what actually fails, what it costs in Phoenix, and what the repair involves. If you’d rather skip the reading and get a flat price, call (623) 404-9080 and we’ll walk you through it. Marcus Deller and our crew have been servicing LiftMaster doors across the Phoenix metro for years, from Desert Ridge down to Laveen.
Which LiftMaster Models This Applies To
Most residential LiftMaster doors in Phoenix fall into a few broad groups, and the cable-and-drum setup follows the spring configuration more than the opener model. If your door has a torsion spring above the opening (the spring on a bar, not the two stretched springs on the sides), the drums sit at each end of that bar, and the cables wind onto them. LiftMaster’s own line covers this indirectly, but the parts themselves are usually industry-standard sizes: 4-inch drums for 7-foot doors, 5-inch or 6-inch drums for 8-foot doors, and cable in 1/8-inch or 3/32-inch diameter, depending on door weight.
Here’s the compatibility gotcha most Phoenix homeowners hit: the drum size must match the door height, not the opener brand. A 7-foot door with a 4-inch drum moves very differently from an 8-foot door with the same 4-inch drum. We’ve seen doors where a previous repair left the wrong drum on, and the cable spooled unevenly until it snapped. If you’re ordering parts yourself, check the sticker on the side of the door for height and weight, and match the drum to that, not to the LiftMaster logo on the opener.
OEM LiftMaster cables and drums are solid parts, but we also carry quality aftermarket equivalents for about 20-30% less in most cases. The difference is mostly packaging and markup, not metallurgy. We’ll quote both options when there’s a real price difference, and we won’t upsell the OEM version if the aftermarket part does the same job.
For the record: Servo Garage Doors Phoenix is an independent service provider. We’re not affiliated with LiftMaster. We service their equipment daily, but we don’t represent them.
Signs Your LiftMaster Cable & Drum Replacement Is Failing

- The door hangs crooked or jams partway up. One cable has either snapped or slipped off its drum, leaving one side of the door unsupported. The opener keeps pushing, and the door fights itself.
- You see frayed or unraveling cable near the bottom bracket. Phoenix’s dry heat doesn’t cause this directly, but repeated door cycles with a poorly balanced spring puts constant tension on the cable strands. When individual strands start poking out, the cable is weeks, not months, from failure.
- A loud bang from the garage, then the door won’t move. That’s usually a cable snapping under load, sometimes taking a drum with it. The door may be stuck in place, and the opener will strain or error out.
- Grinding or scraping noise during operation. A cracked drum can let the cable ride in the wrong groove, rubbing against the bracket or the drum’s edge. You’ll hear it before you see it.
- The door closes too fast on one side. If a cable has slipped a few wraps but hasn’t fully let go, that side drops quicker than the other. This is a sign the drum or cable is no longer holding proper tension.
Each of these has a mechanical cause we can identify in about five minutes with the door in the down position and the opener disengaged. We photograph what we find before quoting anything. That’s Clause 4 of The Haven Standard, and it exists because Marcus Deller has seen too many homeowners quoted for parts that didn’t need replacing.
Before
AfterReplacement Cost & What’s Included
In Phoenix, expect $130-$250 for a complete LiftMaster cable and drum replacement on one side, installed. Both sides usually land around $200-$380, because the labor overlaps and we’re already on the ladder. Here’s the breakdown:
| Line Item | Typical Range |
|---|---|
| Cable pair (both sides) | $30-$70 |
| Drum pair (both sides) | $40-$90 |
| Labor (1-1.5 hours) | $100-$160 |
| Total, one side | $130-$250 |
| Total, both sides | $200-$380 |
What drives the range? Door weight, drum size, and whether the bottom brackets or roller carriers also need attention. A heavier wood or carriage-style door needs heavier cable, which costs a bit more. We write the full price, part numbers included, before any work begins. Clause 1 of The Haven Standard says the written scope comes first, and we’ve never done a job without it. You’ll also get a documented photo record of the old parts and the new ones installed before we leave, and the work carries our 365-Day Done Right Promise. If it’s not right, we come back and make it right.
DIY or Call Us?

Here’s the honest split. You can safely check a few things without touching a tool: look at whether the cable is frayed, note which side is hanging lower, and see if the drum has visible cracks. That’s useful information to have when you call.
Beyond that, this is not a beginner’s repair. Those cables are under serious tension from the torsion spring, and if you release that tension wrong, the spring can unload its energy in a fraction of a second. In Arizona garages, where doors cycle multiple times a day in summer heat, those springs carry a lot of stored force. The cable snapping while you’re working near the drum is a hospital trip, not a learning experience. We recommend a trained professional for any work on cables, drums, or springs. Per our own policy, even our technicians never work on a loaded spring without the proper winding bars and a second set of eyes on the door.
If you want to know whether it’s a $130 one-side fix or a $380 both-sides job before anyone touches the door, call (623) 404-9080. We’ll give you an honest read over the phone, and if we’re wrong when we get there, the written quote will show it before you spend a dollar.
FAQs
Expect 7 to 10 years from cables and drums under normal use, though Phoenix’s summer heat and frequent cycling can shorten that. Doors used four to six times daily in desert heat will see cable wear faster than a garage kept closed most of the week. The spring’s balance matters more than the cable’s age. Call (623) 404-9080 and we can check the whole system while we’re there.
No. A frayed cable is a failed cable, and patching or splicing it creates a weak point that will snap again, usually at the worst moment. Replacement is the only safe fix, and it’s also the cheaper fix compared to the damage a snapped cable can do to the door or the car. For an exact price on your door, call (623) 404-9080.
Most jobs take about one hour on site for one side, closer to an hour and a half for both. We show up with the parts on the truck, quote the price in writing before starting, and you’ll have a photo record of the finished work before we leave. Schedule by calling (623) 404-9080.
Yes. We carry common 4-inch and 6-inch drums and 1/8-inch and 3/32-inch cable in our Phoenix trucks, which covers the large majority of residential LiftMaster doors we see. If your door needs an uncommon size, we’ll have it sourced same day in most cases. Call (623) 404-9080 and we’ll tell you what fits before you commit to anything.
Written by Marcus Deller, Owner & Lead Technician, Servo Garage Doors Phoenix at Servo Garage Doors Phoenix, serving Phoenix and nearby areas.






Before
After
Before
After